Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit.
Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.
It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.
For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port.
Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link.
This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838.
Copper port auto negotiates for network speed with Auto MDI-X for easy cabling
LEDs indicate when it is feeding PoE or power is interrupted
Supports 802.3x flow control on full-duplex ports and backpressure on 10BASE-T/100BASE-TX half-duplex ports
Far-end fault detection prevents the loss of data
Link fault passthrough monitors both copper and fiber ports
Powered device signature sending detects when a PoE device is connected
Power PoE devices over the same CATx link used for data communications
https://www.trivoshop.com/black-box-gb-poe-med-conv-10-100-1000mb-cop-to-1000mb-mm-fbr-850nm-550m-sc-ets2892071240975Black Box Gb PoE MED CONV 10/100/1000Mb COP to 1000Mb MM FBR 850nm 550m SChttps://www.trivoshop.com/media/catalog/product/8/0/80838365.jpg337.55337.55USDInStock/Network & Communication/Network & Communication/Transceivers/Media Converters/Top Categories/Networking & Communications31327728Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. <p>Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.</p> <p>It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.</p> <p>For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port.</p> <p>Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link. <br /> <br />This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838.</p><br><ul><li>Copper port auto negotiates for network speed with Auto MDI-X for easy cabling</li><li>LEDs indicate when it is feeding PoE or power is interrupted</li><li>Supports 802.3x flow control on full-duplex ports and backpressure on 10BASE-T/100BASE-TX half-duplex ports</li><li>Far-end fault detection prevents the loss of data</li><li>Link fault passthrough monitors both copper and fiber ports</li><li>Powered device signature sending detects when a PoE device is connected</li><li>Power PoE devices over the same CATx link used for data communications</li></ul>00add-to-cartsku:ETS2892071description:Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. <p>Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.</p> <p>It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.</p> <p>For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port.</p> <p>Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link. <br /> <br />This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838.</p><br><ul><li>Copper port auto negotiates for network speed with Auto MDI-X for easy cabling</li><li>LEDs indicate when it is feeding PoE or power is interrupted</li><li>Supports 802.3x flow control on full-duplex ports and backpressure on 10BASE-T/100BASE-TX half-duplex ports</li><li>Far-end fault detection prevents the loss of data</li><li>Link fault passthrough monitors both copper and fiber ports</li><li>Powered device signature sending detects when a PoE device is connected</li><li>Power PoE devices over the same CATx link used for data communications</li></ul>price:337.550000weight:2.600000image:/8/0/80838365.jpgsmall_image:/8/0/80838365.jpgthumbnail:/8/0/80838365.jpgstatus:Enabledvisibility:Catalog, Searchcustom_design:-- Please Select --page_layout:No layout updatesoptions_container:Block after Info Columncreated_at:2022-10-01 11:08:01updated_at:2022-10-01 11:08:01country_of_manufacture: custom_layout:No layout updatesmsrp:429.990000msrp_display_actual_price_type:Use configprice_view:Price Rangeshipment_type:Togethergift_message_available:Noswatch_image:/8/0/80838365.jpgtax_class_id:Taxable Goodsproduct_name:Gb PoE MED CONV 10/100/1000Mb COP to 1000Mb MM FBR 850nm 550m SCwidth:6.2"product_type:Transceiver/Media Converterheight:1.6"manufacturer_part_number:LPS500A-MM-SCcountry_of_origin:Taiwanlimited_warranty:2 Yearbrand_name:Black Boxproduct_model:LPS500A-MM-SCweight_approximate:1.30 lbdepth:5.2"product_series:LPS500environmental_certification:RoHSenvironmentally_friendly:Yestaa_compliant:Yeswesupply_estimation_display:Yesin_html_sitemap:Yesuse_in_crosslinking:Yesin_xml_sitemap:Yesstripe_sub_enabled:Nogoogleshopping_exclude:Nofeatured:Nosw_featured:Nosku:ETS2892071description:Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. <p>Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.</p> <p>It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.</p> <p>For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port.</p> <p>Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link. <br /> <br />This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838.</p><br><ul><li>Copper port auto negotiates for network speed with Auto MDI-X for easy cabling</li><li>LEDs indicate when it is feeding PoE or power is interrupted</li><li>Supports 802.3x flow control on full-duplex ports and backpressure on 10BASE-T/100BASE-TX half-duplex ports</li><li>Far-end fault detection prevents the loss of data</li><li>Link fault passthrough monitors both copper and fiber ports</li><li>Powered device signature sending detects when a PoE device is connected</li><li>Power PoE devices over the same CATx link used for data communications</li></ul>price:337.550000weight:2.600000image:/8/0/80838365.jpgsmall_image:/8/0/80838365.jpgthumbnail:/8/0/80838365.jpgstatus:Enabledvisibility:Catalog, Searchcustom_design:-- Please Select --page_layout:No layout updatesoptions_container:Block after Info Columncreated_at:2022-10-01 11:08:01updated_at:2022-10-01 11:08:01country_of_manufacture: custom_layout:No layout updatesmsrp:429.990000msrp_display_actual_price_type:Use configprice_view:Price Rangeshipment_type:Togethergift_message_available:Noswatch_image:/8/0/80838365.jpgtax_class_id:Taxable Goodsproduct_name:Gb PoE MED CONV 10/100/1000Mb COP to 1000Mb MM FBR 850nm 550m SCwidth:6.2"product_type:Transceiver/Media Converterheight:1.6"manufacturer_part_number:LPS500A-MM-SCcountry_of_origin:Taiwanlimited_warranty:2 Yearbrand_name:Black Boxproduct_model:LPS500A-MM-SCweight_approximate:1.30 lbdepth:5.2"product_series:LPS500environmental_certification:RoHSenvironmentally_friendly:Yestaa_compliant:Yeswesupply_estimation_display:Yesin_html_sitemap:Yesuse_in_crosslinking:Yesin_xml_sitemap:Yesstripe_sub_enabled:Nogoogleshopping_exclude:Nofeatured:Nosw_featured:Nosku:ETS2892071description:Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. <p>Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.</p> <p>It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.</p> <p>For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port.</p> <p>Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link. <br /> <br />This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838.</p><br><ul><li>Copper port auto negotiates for network speed with Auto MDI-X for easy cabling</li><li>LEDs indicate when it is feeding PoE or power is interrupted</li><li>Supports 802.3x flow control on full-duplex ports and backpressure on 10BASE-T/100BASE-TX half-duplex ports</li><li>Far-end fault detection prevents the loss of data</li><li>Link fault passthrough monitors both copper and fiber ports</li><li>Powered device signature sending detects when a PoE device is connected</li><li>Power PoE devices over the same CATx link used for data communications</li></ul>price:337.550000weight:2.600000image:/8/0/80838365.jpgsmall_image:/8/0/80838365.jpgthumbnail:/8/0/80838365.jpgstatus:Enabledvisibility:Catalog, Searchcustom_design:-- Please Select --page_layout:No layout updatesoptions_container:Block after Info Columncreated_at:2022-10-01 11:08:01updated_at:2022-10-01 11:08:01country_of_manufacture: custom_layout:No layout updatesmsrp:429.990000msrp_display_actual_price_type:Use configprice_view:Price Rangeshipment_type:Togethergift_message_available:Noswatch_image:/8/0/80838365.jpgtax_class_id:Taxable Goodsproduct_name:Gb PoE MED CONV 10/100/1000Mb COP to 1000Mb MM FBR 850nm 550m SCwidth:6.2"product_type:Transceiver/Media Converterheight:1.6"manufacturer_part_number:LPS500A-MM-SCcountry_of_origin:Taiwanlimited_warranty:2 Yearbrand_name:Black Boxproduct_model:LPS500A-MM-SCweight_approximate:1.30 lbdepth:5.2"product_series:LPS500environmental_certification:RoHSenvironmentally_friendly:Yestaa_compliant:Yeswesupply_estimation_display:Yesin_html_sitemap:Yesuse_in_crosslinking:Yesin_xml_sitemap:Yesstripe_sub_enabled:Nogoogleshopping_exclude:Nofeatured:Nosw_featured:NoBlack BoxTaiwan2022-10-01 11:08:01-- Please Select --No layout updates5.2"Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. <p>Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.</p> <p>It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.</p> <p>For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port.</p> <p>Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link. <br /> <br />This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838.</p><br><ul><li>Copper port auto negotiates for network speed with Auto MDI-X for easy cabling</li><li>LEDs indicate when it is feeding PoE or power is interrupted</li><li>Supports 802.3x flow control on full-duplex ports and backpressure on 10BASE-T/100BASE-TX half-duplex ports</li><li>Far-end fault detection prevents the loss of data</li><li>Link fault passthrough monitors both copper and fiber ports</li><li>Powered device signature sending detects when a PoE device is connected</li><li>Power PoE devices over the same CATx link used for data communications</li></ul>YesRoHSNoNoNo1.6"/8/0/80838365.jpgYesYes2 YearLPS500A-MM-SC429.990000Use configBlock after Info ColumnNo layout updates337.550000Price RangeLPS500A-MM-SCGb PoE MED CONV 10/100/1000Mb COP to 1000Mb MM FBR 850nm 550m SCLPS500Transceiver/Media ConverterTogetherETS2892071/8/0/80838365.jpgEnabledNo/8/0/80838365.jpgNoYesTaxable Goods/8/0/80838365.jpg2022-10-01 11:08:01YesCatalog, Search2.6000001.30 lbYes6.2"
